โšก Automated Preflight Update โ€” Compatible with all 3DR Solo Systems, any version

The Complete
On-Board Management Console
for Your 3DR Solo

Bypass defunct 3DR cloud servers forever. Perform the complete automated Preflight Update, flash latest ArduCopter stable version, calibrate sensors, tune flight parameters, and stream live HDMI video with real-time FPV On-Screen Display (OSD) โ€” directly from any browser on any phone, tablet, or PC.

Resides permanently on the drone ยท Zero apps required ยท Works 100% offline via SoloLink Wi-Fi

1-Click
Preflight Update
Live FPV
HDMI Video + OSD
Black & Green
Cube Autopilots
1,000+
Live MAVLink Params
100%
Offline Self-Contained

Automated Preflight Update: Free Your Solo From the Loop

When 3D Robotics decommissioned their cloud update infrastructure, Solos around the world became trapped in the infamous "Preflight Update Required" prompt. The Solo Web Utility permanently solves this with an all-in-one, fully automated on-board firmware engine.

Rescue, Modernize & Upgrade in One Step

Upgrades the complete drone stack to modern firmware โ€” compatible with all 3DR Solo Systems, any version, without legacy mobile apps or cloud servers.

โœ… The Solo Web Utility Solution

Complete 1-Click On-Board Update

All firmware images and update logic are stored permanently on the Solo's internal 6.5 GB storage partition. With a single click in your browser, the automated pipeline stages and flashes the Cube autopilot, Copter Linux OS, and Controller Linux OS, permanently clearing the Preflight lock.

Hardware Compatibility:
โฌ› Stock Solo Cube (Black) ๐ŸŸฉ Green Cube (latest ArduCopter stable version)
1-Click toggle dynamically selects between arducopter_solo.apj and arducopter_green.apj. Both share the exact same battle-tested Linux system rootfs.

Everything You Need. In One Browser Tab.

Beyond firmware modernization, the Solo Web Utility provides a full flight deck and maintenance suite right from your browser.

โšก

Automated Firmware & Preflight

Complete drone stack deployment across Cube, Copter, and Controller. Compatible with all 3DR Solo Systems, any version. Includes Full Install or Cube-Only modes with live terminal output and an 8-minute reboot timer that survives page refreshes.

๐ŸŽฏ

Cockpit HUD & Live HDMI Video with FPV OSD

Real-time Primary Flight Display (PFD) artificial horizon, pitch ladder, roll arc, moving airspeed/altitude tape instruments, and ultra-low latency H.264 video streamed directly from the Solo's onboard HDMI capture via JMuxer. Includes toggleable real-time FPV On-Screen Display (OSD) overlay reporting GPS coordinates, satellites, HDOP, home distance/bearing, battery voltage, individual cell voltages (Cell 1โ€“4), current draw, flight time, and signal RSSI.

โš™๏ธ

Live Parameter Tuning & Search

Search and modify all 1,000+ ArduPilot parameters with real-time MAVLink read/write on UDP port 14560. Commits directly to the Pixhawk flight controller with instant ACK verification, plus .param file import and export.

๐Ÿ“

6-Axis Accelerometer Calibration

Full interactive 6-position accelerometer and IMU calibration wizard. Guided visual orientation cards (Level โ†’ Left โ†’ Right โ†’ Nose Down โ†’ Nose Up โ†’ On Back) with real-time MAVLink telemetry feedback from the Pixhawk sensors.

๐Ÿงญ

Compass Calibration ("The Solo Dance")

Dual-magnetometer compass calibration with guided 3-axis rotation cards, live per-compass progress bars, and real-time fitness scores. Automatically reboots the Pixhawk after 3 seconds upon completion to lock in magnetic offsets.

๐Ÿ“ถ

Wi-Fi & Bi-Directional NAT Routing

Connect the Controller to your home 2.4 GHz Wi-Fi while keeping the SoloLink AP active. Built-in IP forwarding and NAT masquerade enable your home computer to reach 10.1.1.10 directly without disconnecting from home internet.

๐ŸŽฎ

Interactive Artoo Controller Setup

Interactive SVG diagram of the 3DR Artoo Controller with clickable buttons. Customize Short Hold and Long Hold actions for A, B, Preset 1, Preset 2, and Camera buttons written directly to /usr/bin/extSettings.conf on the Solo.

๐Ÿ”’

On-Board Security & Password Management

Protected web interface with SHA-256 salted password hashing and 24-hour session management. Built-in modal to change passwords directly in the browser, plus a command-line password reset tool.

Tested Presets for Common Solo Mods

Apply battle-tested parameter configurations with a single click. Each preset writes directly to the Pixhawk flight controller via MAVLink with full ACK verification โ€” no manual Mission Planner typing required.

Navigation
๐Ÿงญ

Here 1 / Here 2 GPS Compass

Sets COMPASS_ORIENT = 0 for Here GPS units mounted upright facing forward.

Navigation
๐Ÿงญ

Stock Solo Leg Compass

Restores factory COMPASS_ORIENT = 38 for the stock compass in the Solo leg.

Airframe
๐Ÿ›ฌ

Retractable Landing Gear

Configures Servo 7 output, RC7 toggle, and automatic deploy/retract in RTL and Land modes.

Payload
๐ŸŽฃ

Bait Drop / Payload Release

Gripper servo on Servo 8 with RC8 controller trigger. Grab at 1000ยตs, release at 2000ยตs.

Flight Performance
โšก

Sport Mode (High Velocity)

15 m/s cruise, 12 m/s loiter, 35ยฐ lean angle, and faster climb/descent rates for agile flying.

Flight Performance
๐ŸŽฌ

Cinematic Mode (Smooth)

Ultra-smooth accelerations and gentle braking optimized for stabilized video and photography.

Battery & Power
๐Ÿ”‹

Stock 4S LiPo Battery

Factory 4S LiPo failsafe thresholds โ€” 14.0V Low RTL, 13.5V Critical RTL, SMBus monitoring.

Battery & Power
โšก

4S Li-ion (Madhacker / High-Cap)

Optimized for 18650/21700 Li-ion packs โ€” lowered cutoffs (11.6V/11.3V) with Smart RTL.

Up and Running in Minutes

A one-time Windows installer uploads the utility directly to your Solo. After that, it lives permanently on the drone โ€” no reinstallation needed, even after power cycles.

Download the Installer

Grab Solo Web Utility Installer.exe โ€” a single standalone Windows executable. No Python, Git, or dependencies needed on your PC.

Connect to SoloLink Wi-Fi

Power on your Solo and Controller, then connect your PC to the SoloLink Wi-Fi network as you normally would.

Run the Installer

Double-click Solo Web Utility Installer.exe. It automatically connects via SSH, uploads all files, verifies syntax, and starts the web server on port 80.

Open Your Browser

Navigate to http://10.1.1.10 from any device connected to SoloLink. The utility is live and will persist across reboots permanently.

Lives on Your Solo. Always Available.

The utility runs natively on the Solo Copter's onboard i.MX6 Linux companion computer โ€” not on your phone or PC. It's always available at http://10.1.1.10 the instant you connect to SoloLink Wi-Fi.

On-Board Architecture

Written entirely in Python 2.7 for native compatibility with the Solo's embedded Linux environment. Zero external dependencies on the drone side.

  • Runs directly on the Solo's i.MX6 companion computer
  • Persists across power cycles via /etc/rc.local auto-start
  • Installed on /log/SoloWebUtility (6.5 GB persistent ext4 storage)
  • Web server on port 80 โ€” accessible from any browser
  • MAVLink telemetry via UDP port 14560 through telem_forwarder
  • Direct Pixhawk parameter read/write with ACK verification
  • No internet connection required โ€” fully self-contained
  • Works on any phone, tablet, laptop, or desktop with a browser
  • Compatible with all 3DR Solo Systems, any version
# One-time install from Windows PC: > deploy_to_solo.exe # Connects to Solo via SSH (10.1.1.10) # Uploads web server + firmware files # Starts server on port 80 # Configures auto-start on boot # Then from ANY device on SoloLink Wi-Fi: Browser โ†’ http://10.1.1.10 # That's it. Available forever. # Complete Preflight Update ready. # No apps. No cables. No GCS.

Get the Solo Web Utility

Free, open-source, and 100% self-contained on-board drone software. Download the installer, Android helper app, or read the complete Owner's Manual below.

๐ŸชŸ

Windows Installer

Single executable (Solo Web Utility Installer.exe). Automatically connects to Solo via SSH on SoloLink Wi-Fi, installs the web server, configures persistent boot startup, and launches the app.

๐Ÿ’พ Download Windows Installer (.exe) (~160 MB)
๐Ÿ“ฑ

Sololink Viewer APK

Lightweight Android application (Solo Web Utility Installer.apk) providing direct web console view and seamless video handoff on Android devices connected to SoloLink Wi-Fi.

๐Ÿ“ฑ Download Android APK (.apk) (~296 MB)
๐Ÿ“–

Owner's Manual

Complete 11-section documentation covering system architecture, Preflight update engine, Wi-Fi NAT router, Cockpit OSD HUD, calibrations, parameters, and controller setup.

๐Ÿ“„ User Manual PDF ๐Ÿ“– User Manual Online

Zero external dependencies on PC or drone ยท Permanent on-board storage ยท Works 100% offline via SoloLink Wi-Fi

Honoring the Solo Developer Legacy

The 3DR Solo community owes immense gratitude to the visionary developers who kept the Solo ecosystem thriving over the years.

๐Ÿ“ฑ

Solex

Solex is a highly capable, full-featured, current app receiving updates for Android pilots, offering rich shot management, custom flight modes, and advanced ground control.

โœˆ๏ธ

SidePilot

SidePilot is a highly capable, full-featured, current app receiving updates for iOS aviators, providing flight planning, real-time telemetry, and seamless ArduPilot integration.

The Solo Web Utility operates directly on the drone's Linux companion computer as an on-board maintenance console for automated firmware upgrades, parameter setup, and sensor calibration. It is designed to work in harmony alongside Solex, SidePilot, QGroundControl, and Mission Planner.