Bypass defunct 3DR cloud servers forever. Perform the complete automated Preflight Update, flash latest ArduCopter stable version, calibrate sensors, tune flight parameters, and stream live HDMI video with real-time FPV On-Screen Display (OSD) โ directly from any browser on any phone, tablet, or PC.
Resides permanently on the drone ยท Zero apps required ยท Works 100% offline via SoloLink Wi-Fi
When 3D Robotics decommissioned their cloud update infrastructure, Solos around the world became trapped in the infamous "Preflight Update Required" prompt. The Solo Web Utility permanently solves this with an all-in-one, fully automated on-board firmware engine.
Upgrades the complete drone stack to modern firmware โ compatible with all 3DR Solo Systems, any version, without legacy mobile apps or cloud servers.
All firmware images and update logic are stored permanently on the Solo's internal 6.5 GB storage partition. With a single click in your browser, the automated pipeline stages and flashes the Cube autopilot, Copter Linux OS, and Controller Linux OS, permanently clearing the Preflight lock.
arducopter_solo.apj and arducopter_green.apj. Both share the exact same battle-tested Linux system rootfs.
Beyond firmware modernization, the Solo Web Utility provides a full flight deck and maintenance suite right from your browser.
Complete drone stack deployment across Cube, Copter, and Controller. Compatible with all 3DR Solo Systems, any version. Includes Full Install or Cube-Only modes with live terminal output and an 8-minute reboot timer that survives page refreshes.
Real-time Primary Flight Display (PFD) artificial horizon, pitch ladder, roll arc, moving airspeed/altitude tape instruments, and ultra-low latency H.264 video streamed directly from the Solo's onboard HDMI capture via JMuxer. Includes toggleable real-time FPV On-Screen Display (OSD) overlay reporting GPS coordinates, satellites, HDOP, home distance/bearing, battery voltage, individual cell voltages (Cell 1โ4), current draw, flight time, and signal RSSI.
Search and modify all 1,000+ ArduPilot parameters with real-time MAVLink read/write on UDP port 14560. Commits directly to the Pixhawk flight controller with instant ACK verification, plus .param file import and export.
Full interactive 6-position accelerometer and IMU calibration wizard. Guided visual orientation cards (Level โ Left โ Right โ Nose Down โ Nose Up โ On Back) with real-time MAVLink telemetry feedback from the Pixhawk sensors.
Dual-magnetometer compass calibration with guided 3-axis rotation cards, live per-compass progress bars, and real-time fitness scores. Automatically reboots the Pixhawk after 3 seconds upon completion to lock in magnetic offsets.
Connect the Controller to your home 2.4 GHz Wi-Fi while keeping the SoloLink AP active. Built-in IP forwarding and NAT masquerade enable your home computer to reach 10.1.1.10 directly without disconnecting from home internet.
Interactive SVG diagram of the 3DR Artoo Controller with clickable buttons. Customize Short Hold and Long Hold actions for A, B, Preset 1, Preset 2, and Camera buttons written directly to /usr/bin/extSettings.conf on the Solo.
Protected web interface with SHA-256 salted password hashing and 24-hour session management. Built-in modal to change passwords directly in the browser, plus a command-line password reset tool.
Apply battle-tested parameter configurations with a single click. Each preset writes directly to the Pixhawk flight controller via MAVLink with full ACK verification โ no manual Mission Planner typing required.
Sets COMPASS_ORIENT = 0 for Here GPS units mounted upright facing forward.
Restores factory COMPASS_ORIENT = 38 for the stock compass in the Solo leg.
Configures Servo 7 output, RC7 toggle, and automatic deploy/retract in RTL and Land modes.
Gripper servo on Servo 8 with RC8 controller trigger. Grab at 1000ยตs, release at 2000ยตs.
15 m/s cruise, 12 m/s loiter, 35ยฐ lean angle, and faster climb/descent rates for agile flying.
Ultra-smooth accelerations and gentle braking optimized for stabilized video and photography.
Factory 4S LiPo failsafe thresholds โ 14.0V Low RTL, 13.5V Critical RTL, SMBus monitoring.
Optimized for 18650/21700 Li-ion packs โ lowered cutoffs (11.6V/11.3V) with Smart RTL.
A one-time Windows installer uploads the utility directly to your Solo. After that, it lives permanently on the drone โ no reinstallation needed, even after power cycles.
Grab Solo Web Utility Installer.exe โ a single standalone Windows executable. No Python, Git, or dependencies needed on your PC.
Power on your Solo and Controller, then connect your PC to the SoloLink Wi-Fi network as you normally would.
Double-click Solo Web Utility Installer.exe. It automatically connects via SSH, uploads all files, verifies syntax, and starts the web server on port 80.
Navigate to http://10.1.1.10 from any device connected to SoloLink. The utility is live and will persist across reboots permanently.
The utility runs natively on the Solo Copter's onboard i.MX6 Linux companion computer โ not on your phone or PC.
It's always available at http://10.1.1.10 the instant you connect to SoloLink Wi-Fi.
Free, open-source, and 100% self-contained on-board drone software. Download the installer, Android helper app, or read the complete Owner's Manual below.
Single executable (Solo Web Utility Installer.exe). Automatically connects to Solo via SSH on SoloLink Wi-Fi, installs the web server, configures persistent boot startup, and launches the app.
Lightweight Android application (Solo Web Utility Installer.apk) providing direct web console view and seamless video handoff on Android devices connected to SoloLink Wi-Fi.
Complete 11-section documentation covering system architecture, Preflight update engine, Wi-Fi NAT router, Cockpit OSD HUD, calibrations, parameters, and controller setup.
Zero external dependencies on PC or drone ยท Permanent on-board storage ยท Works 100% offline via SoloLink Wi-Fi
The 3DR Solo community owes immense gratitude to the visionary developers who kept the Solo ecosystem thriving over the years.
The Solo Web Utility operates directly on the drone's Linux companion computer as an on-board maintenance console for automated firmware upgrades, parameter setup, and sensor calibration. It is designed to work in harmony alongside Solex, SidePilot, QGroundControl, and Mission Planner.